Jooby Sensor Essential

Radar motion detector for luminaires

Sensors

One or two 24 GHz radars

Data transmitted

LoRa, Wi-Fi (optional)

Power supply

24 V DC (or optional 220 V power adapter)

Product information

General information Wireless connectivity

Jooby Sensor Essential is designed to detect moving objects near the luminaire to adjust light intensity.

The device uses low-power 24 GHz radar sensors for motion detection.

General information

  • Detects any road users, e.g., pedestrians, bicycle riders, and vehicles
  • Generates control signals for appropriately configured connected luminaires to adjust their brightness
  • Designed to be installed 4–6 m high
  • Pedestrian and vehicle detection—up to 15 m and 30 m respectively
  • Can house up to two radar sensors to achieve the desired detection zone shape
  • Uses a DC power supply and can be connected to a green energy generation system without additional transducers.
  • Uses LoRaWAN® technology for centralized configuration and device monitoring
  • Can be equipped with an optional Wi-Fi interface for quick on-site configuration

Technical data

Input voltage

24 V DC or 220 V AC with a power adapter

Power load, max.

2 W

Ingress protection (EN 60529)

IP66

Dimensions

∅ 85 mm

Weight

0,15 kg

LoRa wireless technology, LoRaWAN® network technology

Jooby Sensor Essential supports communication over LoRaWAN® wireless networks, providing the following benefits:

  • Licence-free frequency bands
  • Long range
  • Secure connection with two levels of encryption
  • Low power consumption

LoRaWAN® specifications

Modulation

LoRa™ Spread-Spectrum class C

Receiver sensitivity, dBm

−118 … –136 dBm

Data rate, bit/s

0.250–11 Kbps

Line-of-sight range

up to 15,000 m

Frequency band 1

868.0–868.6 MHz

Radiated power

25 mW (14 dBm)

Pulse ratio

<1 %

Frequency bandwidth

125 kHz

Frequency band 2

867.0–868.0 MHz

Radiated power

25 mW (14 dBm)

Pulse ratio

<0,1 %

Frequency bandwidth

125; 250 kHz

Frequency band 3 (receive)

869.4–869.65 MHz

Pulse ratio

<10 %

Frequency bandwidth

125 kHz

ShortLink technology

The device supports ShortLink technology to connect luminaires to one another. ShortLink enables dynamic lighting—when a motion sensor is triggered on one luminaire, the brightness on the nearby ones is raised, too. The system thus creates a ‘light wave’ in front of the moving pedestrian or car. ShortLink technology reduces the devices’ response delay to 0.01 s.

Modulation

LoRa™ Spread-Spectrum

Frequency band

869.7–870 MHz

Frequency bandwidth

250 kHz

Radiated power

5 mW (7 dBm)

Receiver sensitivity, dBm

-120 dBm

Data rate, bit/s

0.250–11 Kbps

Line-of-sight range

Up to 1 km

Wi-Fi debugging interface

Jooby Sensor Essential can be equipped with a Wi-Fi module, which can be used for testing, luminaire restarting, and firmware updates.

Wi-Fi protocol

IEEE 802.11 b/g/n

Frequency band

2.4–2.5 GHz (2,400–2,483.5 MHz)

Radiated power

14 dBm (@ 72.2 Mbps), 20 dBm (@ 802.11b)

Receiver sensitivity, dBm

−72 … −98 dBm

Security

WPA/WPA2

Encryption

WEP/TKIP/AES

Network protocol

IPv4, TCP/UDP/HTTP/FTP

Line-of-sight range

Up to 100 m

Light control panel

Luminaire location map
Daily luminaire operation programme
Annual luminaire operation programme
Luminaire operation statistics as diagrams

How our Smart Lighting solution works

Devices

LoRaWAN® base station network

Jooby CMS software

Technical support

Avenue Smart Cover

To transform a regular Avenue luminaire into a smart one, an Avenue Smart Cover controller needs to be installed. This enables you to connect your luminaires to Jooby CMS for management and monitoring.

Read more

Case studies

Jooby Avenue’s smart luminaires light streets, parks, roads, bridges, and thermal power plants in Ukraine, Switzerland, and Denmark. Radio modules for utility meters and the Jooby RDC Dashboard solution enable automation of water, gas, heat, and electricity consumption tracking with minimal infrastructure investments.

Ask a question

Choose your project's focus:

By clicking on ‘Submit’, you confirm that you have read, understood, and accept our privacy policy.

Your message has been sent successfully

Thank you, we have received your message. The responsible manager will contact you shortly.

Making a request

By clicking on ‘Submit’, you confirm that you have read, understood, and accept our privacy policy.

Your request has been sent

Thank you, we have accepted your request. In the near future the responsible manager will contact you and clarify the details of the order.

Making a request

By clicking on ‘Submit’, you confirm that you have read, understood, and accept our privacy policy.

Your request has been sent

Thank you, we have accepted your request. In the near future the responsible manager will contact you and clarify the details of the request.